|
Compatibility:
The following vehicles including CAN-BUS equipped models from model
year 1994.
AUDI A2, A3, A4, S4, RS2, A6, S6, A8, S8, TT.
VOLKSWAGEN Golf IV, Golf V, EOS, Q7, Turan, Tuareg, Multivan, New
Beetle, Sharan, Trade Wind, Lupo, Bora, Caddy, T4, T5, Polo.
SEAT Arosa, Ibiza, Cordoba, Alhambra, Superp, Roomster, Toledo, Leon.
SKODA Octavia, Fabia.
FORD Galaxy (Diesel).
|
Easy To Use:
Performs the following reset procedures:
Oil service oil 15000 km
Inspection IN1 30000 km or 365 days
Inspection IN2 30000 km or 730 days
Display passenger car: "service now"
IN1/IN2 "service in..." 15000 km or 365 days
LongLife starting from 6/99 display "service now" or "service
accomplished in..."
Airbag control fully automatic.
Service interval
The next service is shown on the trip recorder in the cockpit. The
service display in the car is identical with the SI605 symbol on the
device.
The following service intervals are programmed with the SI605 :
('94-6/99)
Oil-Oil change - 15000km
IN1-Inspection 1 - 30000km or 365 days
IN2-Inspection 2 - 30000km or 730 days
Display Car: (Longlife)->6/99
"Service now"
"Service in..." - 15000km or 365 days
Long life:
Display Car: "Service now" - "Service in..."
Oil (15000 km) is automatically programmed together with IN1 and IN2.
Resetting the service interval display
1. Switch off ignition.
2. Plug device into car diagnostic system.
3. Select program.
Programming only according to service display in car!
Oil = Oil
IN1 = IN1
IN2 = IN2
"Service in..." = Longlife
"Service now" = Longlife
4. Switch on ignition.
Do not start engine. Can only be programmed with the ignition on.
5. > 6/99
Press the ENTER key briefly. The selected LED goes out for approx. 10
sec. and then comes on again. Switch off ignition. Remove plug. The SI
display (car) goes out.
Longlife Service
6/99 - 2002, 10 sec.
2002 > 120 sec.
When the Store key has been pressed the appropriate LED will go out
for approx. three seconds and the yellow LED will start to flash. You
must now select the oil type and car using the ENTER key table above.
Only after the store key has been pressed again will the selected
service be programmed. The LED will go out and will start to flash
again on the selected service after approx 10 seconds. If you program
the wrong service by mistake, disconnect the OBD plug and start the
previous step again. Always comply with the table. If you program the
system incorrectly every car will run for up to 50,000 km.
Alternatively the system can be reset manually on the combination
instrument to 15,000 km and 365 days.
6. Switch on ignition. (Display goes out). Switch off ignition.
7. Multiple programming, do not perform multiple programs. Work on one
program at a time and disconnect before moving onto next program.
Multiple programming can lead to error displays!
Airbags
1. Switch off the ignition
2. Select the airbag using the SELECT button. The yellow and red LED's
are illuminated.
3. Switch on the ignition.
Push the ENTER button for a short amount of time. The yellow and red
LED's extinguish and illuminate once more after a few seconds. The
error memory of the airbag is cleared.
4. If the airbag lamp stays on, it indicates a continued defect in the
airbag system which must be remedied before the error can be cleared.
Error message
1. All three LEDs flash simultaneously:
If the device does not respond:
Switch off the ignition.
- Device plug not connected properly.
- Short-circuit after plus on the diagnostics line.
- Control device defect.
- New software / update.
- Function does not exist in the control device (Golf 3 / Polo /
Toledo).
2. The yellow and red LEDs flash simultaneously:
- Short-circuit after the earth on the diagnostics line.
3. The selected LED does not come on again after the memory button is
pressed. Disconnect device plug, wait 10 minutes and restart.
4. not performed.
- Car battery voltage too low.
At least 12 volts required.
- Data line faulty.
- Device plug not connected properly (A4).
- New software /update. |
